Enjoy High-Quality Performance with the Symetrix Prism 8x8 Dante

The Prism family is included in the Symetrix line of Dante™ enabled DSPs. Symetrix uses Dante, a multi-channel digital media networking technology, to interconnect multiple Symetrix DSPs, Symetrix I/O expanders, and select third-party Dante enabled devices. Prism is ideally suited for applications requiring powerful, extremely cost effective advanced signal processing coupled with a standardized means for future expansion.

• 8 analog in and out, 64x64 Dante and powerful Symetrix DSP reduce overall system costs.
• Ultra low latency Dante network audio protocol uses standard IT infrastructure.
• Industry leading analog and A/D/D/A performance, 48 volt phantom mic power.
• Configured using award winning Composer software. Controlled from ARC wall panels, ARC-WEB and third-party touchscreens. Embedded webserver enables remote metering and diagnostics.
• Front panel LCD provides configuration information, system status, and analog audio levels.

SPECIFICATIONS

Analog Inputs

• Number of Inputs: Eight (8) switchable balanced mic or line level.
• Connectors: 3.81 mm terminal blocks.
• Nominal Input Level: +4 dBu.
• Maximum Input Level: +23 dBu.
• Mic Pre-amp gain: 0, 12, 24, 44 or 54 dB switchable with ± 24 dB trim.
• Mic Pre-amp EIN: < -125dB with 150 ohm source impedance. 22.4 kHz BW.
• CMRR: > 79 dB @ 1 kHz, unity gain.
• Input impedance: 8k Ohms balanced, 4k Ohms unbalanced.
• Phantom power (per input): +48 VDC, 10 mA maximum.
• Dynamic range: > 113 dB, A-weighted.
• THD+Noise: < -100 dB; 22.4 kHz BW, unweighted; 1 kHz @ +15 dBu with 0 dB gain. Course gain is set to +4dBu.
• A to D Latency: 0.28 mS.

Analog Outputs

• Number of Outputs: Eight (8) balanced line level.
• Connectors: 3.81 mm terminal blocks.
• Nominal Output: Level +4 dBu with 20 dB of headroom.
• Maximum Output: Level +24 dBu (+22.8 dBu into a 2k Ohm minimum load).
• Output Impedance: 300 Ohms balanced, 150 Ohms unbalanced.
• Dynamic Range: > 117 dB, A-weighted.
• THD+Noise: < -97 dB; 22.4 kHz BW, unweighted; 1 kHz, 0 dB gain +8dBu output.
• D to A Latency: 0.60 mS.

System

• Sampling Rate: 48 kHz.
• Frequency Response (A/D/A): 20 Hz – 20 kHz, ± 0.5 dB.
• Dynamic Range (A/D/A): > 113 dB, A-weighted.
• Channel Separation (A/D/A): > 110 dB @ 1 kHz, +24 dBu.
• THD+Noise: < 95 dB (22.4 kHz BW, un-weighted); 1 kHz @ +15 dBu with 0 dB gain.
• Latency (A/D/A): 1.04 mS, inputs routed to outputs.
• Processors: 1 x Analog Devices SHARC 21489 @ 400 MHz SIMD.
• Raw Processing Capacity: 400 MIPS, 1.6 GFLOPS.
• Delay Memory: 174 mono seconds.
• Analog control inputs: 0-3.3 VDC.
• Recommended External Control Potentiometer: 10k Ohm, linear.
• Logic Outputs: Low (0V) when active, pulled high (5V) when inactive.
• Logic Output Maximum External Power Supply Voltage: 24 VDC.
• Logic Output Maximum External Power Supply Current Sinking: 50 mA.
• Logic Output Maximum Output Current: 10 mA.
• RS-485 Serial I/O: 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port.
• Ethernet Cable: Standard CAT5e or CAT6, maximum device-to-device length = 100 meters.
• Dante Cable: Standard CAT6, maximum device-to-device length = 100 meters.
• ARC Cable: Standard CAT5, distance dependent upon load and number of devices. 8 Watts maximum power available.
• Maximum Devices: Per System 80 units per Site File.
• Maximum Stored: Presets 1000.

Mechanical Specifications

• Space Required: 1U (WDH: 18.91 in. x 9.88 in. x 1.72 in. / 48.02 cm x 25.1 cm x 4.37 cm). Depth does not include connector allowance.
• Electrical: 24V 1.4A, 34W Maximum. 
• Ventilation: Maximum recommended ambient operating temperature is 30 C / 86 F

We are Chuck Levin's Washington Music Center

Maryland, Virginia, and Washington DC's legendary music shop. Family-owned and operated since 1958. Buy gear the way it was meant to be bought, from a store that's been there through it all and has the vibe to prove it. We're staffed with musicians and industry experts, people that live and breathe music gear. Our mission is to help you find the right gear for your project, that thing that will bring you the most joy out of what you do. We're an authorized dealer for almost every brand, we stock items the other stores don't, so you can try before you buy. Stop by our Wheaton, MD showroom and see for yourself.

Contact us if you have questions about one of our listings or if you need help finding the right piece of gear.